US $197.46
Original Price : US $229.61 (14%)
Limited Offer DIY RC Drone Quadrocopter RTF X4M360L Frame Kit with GPS APM2.8 AT10 TX F14892-D with FREE Worldwide Shipping!
4.79
Related Products :
M4 M5 M6 Hand Tighten Screw Aluminum Alloy Handle Adjustable Screws DSLR Camera Photography Accessories
XILETU XJ-8 Tripod phone tripod mount Head Bracket Mobile Phone Holder Clip For Phone Flashlight Microphone With Spirit level
JEYI VolleyStar-PRO Black Heat Sink Heatsink M.2 NVMe SSD NGFF TO PCIE X4 Adapter MKey Port Card PCI-E 3.0 x4 Full Speed RGB LED
Aluminum L-type Adjustment Tighten Locking 7-shaped Handle Screw M5 M4 Adjustable Screws DSLR Camera Photographic Parts
Product description
[32624899683]DIY RC Drone Quadrocopter Whole Set X4M360L Frame Kit with GPS APM 2.8 AT10 RX TX Battery Motor ESC RTF Unassembled,buyer need to assemble by themselves.
Package include: 1xX4M360L frame 2x920KV CW Brushless Motor 2x920KV CCW Brushless Motor 4x30A Brushless ESC 2X8443 8.4*4.3" Carbon Fiber Propeller Self-locking Props 1XMK KK Multi-Copter Power Battery to 8 ESC Connection Board 1XAPM 2.8 Flight control 1x6M GPS with Compass 1x5pcs 10cm Servo Receiver Extension Lead Wire Cable 1xGPS Folding Antenna Mount Holder 12x3.5mm banana plug 1xDeans Style T Plug Male Connector Silicone Wire With 11.5CM 14awg 1xHook and & Loop Fastening Tape 1x 11.1V 3300Mah 25C lipo battery Two colors for choose,please tell us which one you prefer in advance,or we will ship it according to our inventory,thanks. Features: Multiple function remote control system,including helicopter,airplane and slider three type flying machine and five models,cover almost every popular model,you can fly any model by this radio. 3.5 inch colorful screen 320×480 resolution,clear display menu and graphs. Great control distance: 1.1km on the ground,2km in the sky. Expansion feedback module,users can get plane details in real time. Make very setting clear and exactly output result. Fast response time only 3ms to the operation,faster then the other transmitter 20ms,even ten channels also let you feel it. High channel resolution reaches 4096,0.25us per resolution let all the servos keep tranquil. Strong anti-jumping,DSSS(Direct sequence spread spectrum) technology. Unbelievable price, high quality as supper bland, and more exactly, faster response, higher resolution,one and the only one anti-jumping DSSS technology.really worthy to have it. Technical Parameter: 1. Dimension:18×9.5×22cm; 2. Weight:0.95kg; 3. Frequency:2.4GHz ISM band(2400MHz~2485MHz); 4. Modulation mode:QSPK; 5. Channel bandwidth:5.0MHz; 6. Spread spectrum:DSSS; 7. Adjacent channel rejection:>38dBM; 8. Transmitter power: <100mW(PCB testing), <20dBm(3 meter air testing); 9. Operating Voltage:8.6~15V; 10. Operating Current:<95mA; 11. Control distance:800 meters ground; 12. Channel:10 Channel,8~10 channel are customizable; 13. Compatible model: Include all 120 degree and 90 degree swashplate helicopter,all fix wing and glider,five flying model; 14. Simulator model:under the simulator model the transmitter action turn off,change to power saving model; 15. Screen:16 colorful screen,size 78×52mm,320*480 pixel. About the APM 2.8 Flight control,here is the user manual Before you can configure your APM, you will need to first connect everything together. This guide willshow you all the cablesand parts that you will need to connect to your APM. Typical Quadcopter Layout Please note the illustration Below highlights a (TYPICAL) installation. It contains optional equipment including a Camera Gimbal and a Battery Monitor and it utilizes an ESC wired "Y" power connection rather than the power distribution board common to many MultiCopters. 1. Connecting your motors and RC gear Overview of connections on the Ardupilot Mega v2 board Note: the instructions below are for regular RC receivers with PWM output (one cable per channel). If you're using a "PPM" receiver (one cable carries all channels), follow the instructions . Before you can configure your Arducopter, you will need to first connecteverythingtogether. This is quite easy. You need to connect your RC receiver to the Input side of the board. You can use the cables included with your Arducopter Kit, or if you are using another frame, you can use jumper cables, or female to female servo cables Connections between RC receiver and Ardupilot Mega v2 board If you are using female to female servo cables, the ground (black) side of each connector must be on the outside for the board, the signal (white/orange) needs to be on the inside as shown below. Connecting with straight connectors Connecting with right angle connectors If you are using a multi-pin connectorthat was included with your Arducopter Kit, connect them as shown below Input Side for RC reciever Output side to PDB Please note, that your ESC, connectors should be plugged in the the output side, it is suggested that you only use power from one of your ESC's. This can be dune by cutting the red wire on all but one of the ESC's, or by using a special adaptor. 2. Connecting ArduCopter motors Once again if you are using an Arducopter Kit, with the PDB, then you dont need to worry about this if you soldered everything correctly as the motors are assigned to the correct pins with the cables you plugged connected in the previous step. However you will neet to make sure your motors are spinning in the correct direction. The images below show the possible arducopter configurations with correct motor orientation Quick Tip: If your motor is not spinning in the correct direction, simply switch the position of any two of the ESC-motor wires. Arducopter Quad Arducopter Tri Arducopter Hexa, Octa, and Y6 Arducopter OCTA QUAD (X8) Connecting a Roll-Tilt Camera mount 3. Connecting Optional Sensors Sonar - Ultrasonic Rangefinder AC2 supports the MaxSonar line of sonars for low level altitude hold and in the future collision avoidance. Below 10 meters sonar is primarily used for altitude hold. Above 10 meters, the barometric sensor is used. GPS is not required for altitude hold. Connect your Ultrasonic Sensor to the A0 port of your Ardupilot Mega v2 board The sonar sensors are quite sensitive to noise, adding something like a ferrite choketo your cable could help. The most important is to mount your sonar away from other electronics like ESC, or wireless telemetry modules. Possible Causes of sonar Interferance Electrical noise caused by ESCs, Servos, or switching BEC's on the same circuit as the Sonar EMF radiation from motors, motor wires, ESC's or Xbee. Acousticnoise from propellers Vibration from motors, props, etc. Optical Flow Sensor The optical flow sensor is used to improve thepositionhold accuracy of your arducopter. This sensor is supported from Arducopter 2.6 and above. Connecting the optical flow sensor to APMv2 Power, GND, NCS pins should be attached to A3 MISO, MOSI and SCLK pins should be directly soldered to the pins shown above Default mounting is lens pointing down, pins forward Its a good idea to secure the wires with some cable ties so they dont break off over time How to connect the optical flow sensor to your ardupilot mega board. Make sure the pins are facing forward Now that everything has been connected everything the next thing to do isconfigure arducopter firmwarefor your frame. If you have any questions or comments please add them below
Important Informaiton to Every Value Clients:
For theSelling Peak Season, someLogistic may delay for some days.especiallye-packet to Russion,Most Western European Countries,and all shipping to Brazil .if you don't receive the parcels on time ,pls help us wait some more days.Pls contact us freelyif you have any questions rather thanmake claimor leave negative feedback without contact.Aliexpress Approved Shipment--China Post Ordinary Small Packet Plusin Selling Peak Season,We guarantee 45 days delivery to main countries ;55 days to Russia; 90 days to Brazil!
