US $90.15
Original Price : US $90.15 (0%)
Special Offer iFlight SucceX Mini F4 V3 TwinG Flight Tower W/SucceX mini 35A V3 ESC/SucceX F4 mini TwinG V3 2-6S with FREE Shipping Worldwide!
4.74
Related Products :
Hole 30x30 Side 35x35 PCB ESC Power Distribution Board for DIY RC Mini Quadcopter Multicopter FPV Drone
4pcs Propeller Guard Prop Protection Cover for 90-130 RC FPV Racer Drone 2/2.5 Inch Blade 1102/1103/1104/1105 Brushless Motor
Tarot 380 HC454-S Motor Transmission Belts 304T TL380A4
4pcs Universal Anti Vibration Ball Dampening Rubber Balls Shock Absorber for Quadcopter 4-axis Camera Gimbal GoPro Hero Drone
Product description
[4000100346082]iFlight SucceX Mini F4 V3 TwinG Flight Tower W/SucceX mini 35A V3 ESC/SucceX F4 mini TwinG V3 2-6S FC/SucceX mini V3 500mW VTX Description:
The SucceX Mini F4 V3 TwinG // GYRO FUSION is the NEXT-GEN flight controller you need for your next build. This FC is ready for anything with 4 uartsWith its clean intuitive layout, the SucceX MINI F4 V3 TwinG makes installation a breeze with a 4 pin connector for your VTX and an10 pin connector that allows simple plug and play connection with your 4in1 ESC.
But the real magic of this flight controller lies in its TWIN GYRO configuration.
The TwinG uses two identical gyros oriented side by side with one offset 90 degrees from the other. Betaflight uses GYRO FUSION to blend and average the information from both gyros to send a much cleaner signal to the PID loop controller! Less noise and fewer oscillations across the throttle band without adding any delay! Betaflight software filters can be lowered in most cases as well, which brings a significant decrease in delay.
With plenty of processing power and uarts, this is the perfect flight controller for long-range GPS builds. And the TwinG configuration makes it the perfect Fc for builds like macro quads, cinematic filming rigs and x-class racers that are a bit trickier to tune.TwinG Gyro Setup
The Betaflight target's default setting is 'gyro_to_use = both' / Gyro fusion is active!
To check the current setting, please use CLI and type 'get gyro' to find the responding entry.
Change the settings with 'set gyro_to_use = ' and type 'save'.
To get the most reliable performance or encounter noise, oscillation and bent props: Please use the default setting 'both".
For Single Gyro use, please use the debugging options to find and tune for the cleaner gyro, but lose the dynamic fusion and averaging.
BF offers the following dual gyro debug options: dual_gyro_raw, dual_gyro, dual_gyro_diff, dual_gyro_combined.
BlackboxLog explorer graph: dual_gyro_raw Debugging = [0] Roll Gyro1, [1] Pitch Gyro1, [2] Roll Gyro2, [3] Pitch Gyro2.
The displayed graph will show the Gyro_Raw reading (no filters applied), both gyros can be compared.SucceX Mini F4 V3 Specifications
MCU:216MHz STM32F405
Gyro:TwinG ICM20689
Blackbox:32MB
OSD:YES
Uarts:4
ESC Telemetry:RX6
INA Pad:nuart2
Input voltage:2-6S,MAX 8S
Target:STM32F405
CLI config:IFLIGHTF4_TWIN_G.config
Size:27*27mm /20*20mm dia3 mountingFC Firmware
Betaflight
Target:STM32F405Physical
Mounting hole:20*20mm,dia3mm with Grommets dia2mm
Size:31*31mmSucceX Mini 35A V3 SPECS:
MCU: STM32F405
Current Sensor: Yes
Input: 2-6s lipo
Telemetry: Yes
Installing Hole: 20x20mm, M3
Target: iFlight-BL32-4IN1
Constant: 35Amps
Burst: 45Amps
Weight:16.7g
Dimensions: 31*31mm(including the power pads)
Mounting Holes: 20*20mm
Supports Dshot1200,Proshot,Oneshot,Multishot5.8G VTX SPECS
Input voltage: 2-6S
48 standard channels, A/B/E/F/R Band
Output Power: pit/20/100/200/500mW
BEC Output: 5V/1A for Camera or FC
RF Connector: MMCX
Video Format: NTSC/PAL
Size: 26*26mm /20*20mm dia3 mountingPackage Included:
SucceX Mini F4 V3 TwinG FC+
SucceX 35A V3 Plus BLHeli_32 4-in-1 ESC
5.8G 500mW VTX
